Internally sealing is not generally required. Low Sheen and Low Sheen Grain both dry to a soft, eggshell finish. The Murobond powder is mixed with WSC Solution or water in the ratio 3 parts powder to 2 parts water to form a paint that is similar in consistency to cream. The thickness of the applied film is critical to cure and performance. Previously Painted Surfaces in Sound Condition The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, efflorescence, mould, algae, moss or other foreign matter. Protection against mechanical abrasion should be provided for at least seven days after application. A liberal coat of Murobond Sealer applied directly from the tin to a dry clean surface by brush, roller or spray.
| Name: | Faushura |
| Format: | JPEG, PNG |
| License: | For Personal Use Only |
| iPhone 5, 5S resolutions | 640×1136 |
| iPhone 6, 6S resolutions | 750×1334 |
| iPhone 7, 7 Plus, 8, 8 Plus resolutions | 1080×1920 |
| Android Mobiles HD resolutions | 360×640, 540×960, 720×1280 |
| Android Mobiles Full HD resolutions | 1080×1920 |
| Mobiles HD resolutions | 480×800, 768×1280 |
| Mobiles QHD, iPhone X resolutions | 1440×2560 |
| HD resolutions | 1280×720, 1366×768, 1600×900, 1920×1080, 2560×1440, Original |
Thin application will show poor cure powdering and excessive weathering. Where this is not practicable, sufficient material to murlbond an elevation should be ordered with any excess used as the first coat on the subsequent elevation.
Murobond Cement Paint
Re-touching of Murobond will show as a distinct patch and unless a consistent patched effect is required, should be avoided. Hairline cracking shrinkage cracking in render murpbond concrete may show through the finished coating and allow excess water to enter the wall.
The Clear Acrylic Sealer will increase sheen level and darken the colour — test an area to ensure satisfactory result before coating entire surface. Allow 12 hours to dry between the coats of Murobomd and before applying Murobond.
Gallery – Murobond Superior Paints
The slightly mottled finish helps unify the appearance while allowing the joints to show. Read More… Woodwash A soft translucent woodwash reminiscent of Scandinavian limed timber.
Following preparation of substrates as previously outlined Murobond Cement paint is applied as follows:. Different amounts may be used in each coat with the lower amount typically being used in the second coat.
Paint Types & Product Information
Initial Protection Adequate protection should be provided against rain and sub-zero temperatures for a period of at least 48 hours after application. View Details Add to cart.
The paints exceptionally resilient formula was developed with protection and performance in mind, making Murobond a wonderful way to enhance cement render, bagging, brickwork or any dimensionally stable surface. Paperfaced Plaster Board and Plaster The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, or mruobond foreign matter.
Previously Painted with a Water-based Paint Externally, apply one liberal coat of Murobond Sealer directly from the tin to a dry clean surface by brush, roller or spray.
Stockists – Murobond Superior Paints
Natural Paint Natural Flat is a natural, breathable water based interior paint, formulated without petrochemicals. The mixed Murobond paint is applied by brush in a random pattern at a rate of approximately 6 sq. This super tough, all purpose paint can be wiped clean without fuss. See Description below for available finishes. View Details Select options. Following preparation of substrates as previously outlined Murobond Cement paint is applied as follows: Cement Render, Bagged Masonry, AAC, Clay or Concrete Murovond or Blocks The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, efflorescence, mould, algae, moss or other foreign matter.
For timbers containing tannin, we advise testing mugobond area before proceeding to application as bleeding of tannin may cause visible staining. If shrinkage cracking is evident, it should be treated by applying one coat of Murobond Sealer over entire surface before the myrobond of Murobond.
This water based formulation is very low VOC, non-yellowing and low odour. Where damage to the existing film is through to a porous underlying structure, these areas should be spot primed with two or more coats of Murobond Primer as necessary to approximate the porosity of the mueobond paint. The mixed Murobond paint is applied in the same manner as the first coat.
Pentimento limewash gives a subtle, mottled patina and its ability to offer unique and individual results makes it a favourite with decorators and renovators. Murowash Murowash offers ,urobond finely grained, streak free flat finish with subtle colour variations. Allow overnight drying before applying Murobond cement paint. Two liberal soaking coats of Murobond Primer are then applied to all surfaces. Previously Painted Surfaces with a Lime Based Coating The surface should be inspected to ensure that it is properly adhering, free of oils, grease, loose particles, dirt, efflorescence, mould, moss or murobohd foreign matter.
Cement finishes such as render, bagging and concrete should be allowed to cure for a minimum of 3 weeks before application of Murobond. Ideal for outdoor walls it can also be used indoors whether the tone is contemporary or traditional. The addition of clean sand to the mjrobond creates an effect similar to bagging, reducing the visual impact of the jointing.
